MXS 10

Powerful professional charging for workshops

MXS 10

Powerful professional charging for workshops

MXS 10

Powerful professional charging for workshops
Image missing

Product information

  • Product information

    Powerful professional charging for workshops

    The ultimate charger

    The MXS 10 gives you state of the art technology and is ideal for professional use in workshops for caravan, RV, boat and car batteries.

    The MXS 10 is a fully automatic 8-step charger that delivers 10A to 12V batteries from 20-200Ah and is also suitable for maintenance charging up to 300Ah. It includes battery diagnosis to establish whether your battery can receive and retain a charge, a Recond mode for restoring and reconditioning stratified and deeply discharged batteries, a winter program for charging in cold weather and an AGM option which maximises the performance life of most Stop/Start batteries. The MXS 10 also has a temperature sensor for optimised charging and it can even be used as a power supply source for 12V equipment.

      ;*;Fully automatic ‘connect and forget’ 8 step charging ;*;Charges batteries from 20-200Ah ;*;Temperature sensor, AGM and Recond programs ;*;Power supply for 12V equipment ;*;2-year warranty
      Technical information
      Input
      220–240VAC, 50–60Hz, 1.4A max
      Output
      14.4V/14.7V/15.8V/13.6V, 10A max
      Start voltage
      2.0V
      Back current drain*
      Corresponding to less than 1Ah/month
      Ambient temperature
      -20˚C to +50˚C
      Battery types
      All types of lead-acid batteries, 12V, WET, MF, Ca/Ca, AGM, GEL
      Battery capacity
      20–300Ah
      Warranty
      2 years
      Insulation class
      IP65
      User manual

      MXS_10-safetyinstruction-AU-EN.pdf

      MXS_10-manual-AU-EN.pdf
    • Inside the box
      CONNECT CLAMP
      Product sheet

      MXS_10-Productsheet-low-UK-EN.pdf
      FAQ
      Temperature LED is not lit   ×
      Explanation: The temperature sensor is disconnected or has been damaged. The charger will assume room temperature and charge without temperature compensation.
      No LED’s are lit on the top row when the charger is connected to both the power outlet and the battery   ×
      The LED’s on the bottom row are lit and you can change charging mode. None of the LED’s in the top row, indicating charging status, are lit.

      Explanation: The battery voltage could be under 2 +/- 0.5V.
      Test: Try to charge the battery in Supply mode for approximately 5 min. Then try regular charging.
      Test: Test the charger on a fresh battery.
      Temperature LED is flashing   ×
      Explanation: The temperature is above + 65 °C. The current is reduced until the temperature has dropped below + 65 °C. The charger reverts to normal charging current when the temperature drops below + 65 °C.
      is flashing   ×
      If no battery or if the battery voltage is too low the led will start to flash to indicate the unit has entered power save mode.
      Test: Test the charger on a fresh battery.
      No LED is lit when the charger is connected only to the power outlet   ×
      Explanation: One of the LED’s at the lower row should light up when the charger is connected to the power outlet.
      Test: Make sure that there is power from the power outlet.
      is lit   ×
      Explanation 1: Reverse polarity.
      Test: Make sure that the + cable/clamp is connected to the + terminal and the – cable/clamp is connected to the – terminal.

      Explanation 2: Loads are connected to the battery which requires more power than the charger can provide.
      Test: Turn off or disconnect the loads when charging.

      Explanation 3: The charger is not connected to a 12V battery.
      Test: Test with a fresh 12V battery.

      Explanation 4: The charge cycle is interrupted in step 1.
      Test: Test to restart the charge cycle, if it still fails in step 1 the battery is sulphated and needs to be replaced.

      Explanation 5: The charge cycle is interrupted in step 4.
      Test: Test to restart the charge cycle, if it still fails in step 4 the battery is can’t be charged and needs to be replaced.
      Temperature LED is lit   ×
      Explanation: This led is turned on automatically when the temp sensor is connected.
      No LED is lit when the charger is connected only to the battery   ×
      Explanation: The plug has to be connected for the LED to be lit.