Helpful pages
D250T is a fully automatic, 4 step DC-DC charger that supplies up to 10A of power to charge any 24V lead-acid service battery. The charger is also a battery isolator that separate the service battery and starter battery to protect the starter battery from being drained when motor is not running.With the D250T you can be confident that the service battery always will receive the optimal charging voltage, with reduced charge time and ensuring the charging will be 100% complete. You will get a stable and efficient charging of the battery that is not dependent in alternator capacity or resistance in cables.D250T will reduce environmental impact and lower the maintenance costs through extended battery life and a reduced idle time.
;*;24V DC-DC battery charger for a system with a starter battery and a service battery. 10A fully automatic 4 step battery charging while you’re on the move.;*;Battery isolator that eliminates the need of diodes and VSR relays. D250T separates the starter battery from the service battery when the engine is not running.;*;Equipped with temperature sensor to compensate charge voltage for hot or cold conditions and to protect battery by switching off the charging if service battery temperature rises too high.;*;Possibility to connect a remote 24V indicator lamp for monitoring the charger status.;*;Totally silent operation due to a cooling system without fans or other moving parts.;*;Minimal installation time and cost.;*;Durable design that is splash and dust proof (IP65);*;Fully compatible with SMARTPASS 120T for the ultimate power management solution up to 130A.;*;2-year warranty;*;SUITABLE FOR: Truck, Heavy Vehicles, Boats, Recreational vehicles, Busses, Transport trucks and all other systems with a 24V battery
| Charging Category | DC charging |
|---|---|
| Input | 25.8–32 V, 10-15 A |
| Output | 28.8 V,10 A |
| Battery types | 24 V:,WET,MF,Ca/Ca,AGM,EFB,GEL |
| Battery chemistry | Lead acid |
| Battery voltage | 24 V |
| Battery capacity | 28–200 Ah |
| Ambient operating temperature | -20 ˚C to +50 ˚C (- 4 °F to +122 °F) |
| Dimensions | 192 x 110 x 65 mm (7.56 × 4.33 × 2.56 in) |
| Degree of protection | IP65 |
| Warranty | 2 years |
| Warranty information | CTEK issues a limited warranty to the original purchaser of the product. Depending on the product, the limited warranty period will vary. The limited warranty is not transferable. The warranty applies to manufacturing faults and material defects. The warranty is void if the product has been handled carelessly or repaired by anyone other than CTEK or its authorized representatives. CTEK makes no warranty other than this limited warranty and is not liable for any other costs other than those mentioned above, i.e. no consequential damages. Moreover, CTEK is not obligated to any other warranty other than this warranty. |
D250T
A 24V DC-DC charger for a heavier duty vehicles
Alternator-based charging - no mains needed
Integrated isolator to protect your starter battery from discharge
The choice for dual batteries, heavy electrical loads or off‑grid power needs
Back in stock alert
Alert is on!
Subscribe to our newsletter and stay updated on the latest fashion pieces and special offers!
We will send you an email when the product is back in stock again
Unable to subscribe. Try again later.
By signing up, I agree with the data protection policy of Ctek.
D250T is a 24V DC-DC battery charger for dual battery systems with starter battery and service battery. D250T is designed to be used as onboard charger for charging and maintaining the service battery from alternator when motor is running, this will give you enough of power in the service battery when arriving to the destination.
Specifications
Battery Voltage
24 V
Battery Capacity
28–200 Ah
Battery Chemistry
Lead acid
Battery types
24 V:,WET,MF,Ca/Ca,AGM,EFB,GEL
Warranty
2 years
Enhance your charging experience
